Skip to main content

Proxmox Cisco VLAN LACP SN3 Config

Devices

  • Mikrotik CCR1009 acting as core router
    • http://10.69.7.13 for the web interface, login admin
    • Also available at 10.70.90.1 as the gateway
    • Manages DHCP leases, VLAN routing
  • Cisco Nexus 5000 acting as a fiber switch
    • ssh -oHostKeyAlgorithms=+ssh-rsa admin@10.70.95.10 to SSH
  • Dell R640 box 1
    • Service tag 12F11Q2
    • Reports one of the power supplies is unpowered
    • 384GB ECC DDR4 2666MHz RAM, 2x Xeon Gold 6152 22C/44T CPUs, 8x 1TB Samsung 870 SATA SSDs configured as RAID-6
    • Plugged with 10G fiber into ports 1/7 and 1/8 of the Nexus 5000 with LACP 802.3ad LAG configured
    • hostname nycmesh-713-r640-01
    • iDRAC https://10.70.90.64 with username root
    • Proxmox WebUI https://10.70.90.195:8006
    • SSH with user root
  • Dell R640 box 2
    • Service tag G60FXQ2
    • hostname nycmesh-713-r640-02
    • 384GB ECC DDR4 2666MHz RAM, 2x Xeon Gold 6152 22C/44T CPUs, 8x 1TB Samsung 870 SATA SSDs configured as RAID-6
    • Plugged with 10G fiber into ports 1/5 and 1/6 of the Nexus 5000 with LACP 802.3ad LAG configured
    • iDRAC https://10.70.90.65 with username root
    • Proxmox WebUI https://10.70.90.196:8006
    • SSH with user root

iDRAC setup

  • Thankfully had DHCP enabled, so it showed up in the Mikrotik DHCP leases, hostnames were idrac-<servicetag>
  • Went to Maintenance, System Update, Manual Update, Location Type HTTPS, use default address, and then Check for Update. It will load some Update Details at the bottom which can then be selected and installed. The Lifecycle log will show updates of the process
    • NOTE: Don't use automatic updates, we can just manually trigger updates when they are useful
    • NOTE: SUP029 warning may indicate that all the firmware is already up to date and of a matching version to what's trying to be updated
    • https://www.dell.com/support/kbdoc/en-us/000134013/dell-poweredge-update-the-firmware-of-single-system-components-remotely-using-the-idrac
  • Went to iDRAC settings and configured the DNS name as nycmesh-713-r640-<id>-idrac-<servicetag>
  • Disabled iDRAC IPV6
  • Enabled iDRAC NTP for 10.10.10.123 and changed timezone to America/New_York
  • Went to Maintenance/Job Queue and System Event Log and cleared both
  • no BIOS settings to change
  • Go to Storage/Virtual Disks and confirm that RAID-0 is not used (it is not redundant). Delete RAID-0 virtual disks and reformat with RAID-6 if possible. Only four disks may be added to RAID-6 at creation, but more can be added in a subsequent step. Cancel initialization (the option might not pop up if there are pending operations), then Edit Disk Capacity and add the remaining drives. Edit the Cache policy, use the (safer) Write-through caching, which means the disk is successfully written to before confirming the write, as opposed to write-back caching where it makes it into cache first and disk later

Cisco Switch Setup

  • Goals
    • Create a LAG/LACP/802.3ad port-channel channel-group for each pair of interfaces going to each server
    • Make the ports trunk ports, meaning all traffic is expected to be tagged with the destination VLAN. Any untagged traffic will be ignored
    • Label the parts of the switch configuration
  • First step: connect to the switch using ssh -oHostKeyAlgorithms=+ssh-rsa admin@10.70.95.10, using the older SSH host key to avoid the error no matching host key type found. Their offer: ssh-rsa https://askubuntu.com/questions/836048/ssh-returns-no-matching-host-key-type-found-their-offer-ssh-dss
  • Then run configure terminal to get into edit mode
  • show run or show running-config will show the full switch configuration. show run interface will show just the part of the configuration for the interfaces, both physical and LAG/LACP
  • show port-channel summary will show already-configured LAG/LACP setups. Same with show port-channel usage. This can help determine which ID number to pick for the new port-channel
  • The following can be pasted in. It will create a port-channel with ID 1, set a text description, set it to trunk mode (all traffic expected to be tagged, versus access mode where traffic is expected to be untagged) and allows it access only to VLAN32. It then duplicates the setup for port-channel ID 2
interface port-channel1
  description nycmesh-713-r640-01 johnb
  switchport mode trunk
  switchport trunk allowed vlan 32

interface port-channel2
  description nycmesh-713-r640-02 johnb
  switchport mode trunk
  switchport trunk allowed vlan 32
  • Then configure the switch ethernet ports for the first server. Set the description, set it to trunk mode and VLAN 32 same as the LACP, and then add it to the channel-group with ID 2 with active mode, indicating 802.3ad LACP
interface Ethernet1/5
  description nycmesh-713-r640-02 wilnil johnb
  switchport mode trunk
  switchport trunk allowed vlan 32
  channel-group 2 mode active

interface Ethernet1/6
  description nycmesh-713-r640-02 wilnil johnb
  switchport mode trunk
  switchport trunk allowed vlan 32
  channel-group 2 mode active
  • Then configure the switch ethernet ports for the second server. Note the shorthand used to configure two ethernet ports at once, int eth 1/7 -8
interface Ethernet1/7-8
  description nycmesh-713-r640-01 wilnil johnb
  switchport mode trunk
  switchport trunk allowed vlan 32
  channel-group 1 mode active
  • Use show lacp neighbor to look to see if a connection was made. If there is nothing connected at the other end, the Partner System ID will probably be all 0s.
nycmesh-sn3-n5k(config-if-range)# show lacp neighbor
Flags:  S - Device is sending Slow LACPDUs F - Device is sending Fast LACPDUs
        A - Device is in Active mode       P - Device is in Passive mode
port-channel1 neighbors
Partner's information
            Partner                Partner                     Partner
Port        System ID              Port Number     Age         Flags
Eth1/7      0,0-0-0-0-0-0          0x0             0           SP

            LACP Partner           Partner                     Partner
            Port Priority          Oper Key                    Port State
            0                      0x0                         0x0

Partner's information
            Partner                Partner                     Partner
Port        System ID              Port Number     Age         Flags
Eth1/8      0,0-0-0-0-0-0          0x0             0           SP

            LACP Partner           Partner                     Partner
            Port Priority          Oper Key                    Port State
            0                      0x0                         0x0

  • Once the other end is configured, the MAC address should show up, as well as the flag showing Active mode
port-channel1 neighbors
Partner's information
            Partner                Partner                     Partner
Port        System ID              Port Number     Age         Flags
Eth1/7      65535,e4-43-4b-18-25-f00x1             1488        SA

            LACP Partner           Partner                     Partner
            Port Priority          Oper Key                    Port State
            255                    0xf                         0x3d

Partner's information
            Partner                Partner                     Partner
Port        System ID              Port Number     Age         Flags
Eth1/8      65535,e4-43-4b-18-25-f00x2             1488        SA

            LACP Partner           Partner                     Partner
            Port Priority          Oper Key                    Port State
            255                    0xf                         0x3d
  • Save the configuration to permanent memory so it will persist between reboots with copy running-config startup-config
  • Other useful commands
    • Get rid of unused port-channels with no interface port-channel 5
    • Trying to set channel-group 1 mode active may result in an error command failed: port not compatible [port allowed VLAN list] which means the allowed VLAN list between the port-channel and the ethernet interface does not match. Get them to match with switchport trunk allowed vlan 32 and then rerun the command and it should work
    • no shutdown apparently will bring a port back online if it were previously disabled for some reason
    • Get a port or set of ports back to its default configuration with default int eth 1/5-8
    • View a port's counters and other info with show int eth 1/5.
    • Clear the port's counters with clear count int eth 1/5
  • A variety of different commands can be used to check status on things as well
nycmesh-sn3-n5k(config)# show int eth1/5-8 brief

--------------------------------------------------------------------------------       
Ethernet      VLAN    Type Mode   Status  Reason                   Speed     Port      
Interface                                                                    Ch #      
--------------------------------------------------------------------------------       
Eth1/5        1       eth  trunk  down    suspended(no LACP PDUs)     10G(D) 2
Eth1/6        1       eth  trunk  down    suspended(no LACP PDUs)     10G(D) 2
Eth1/7        1       eth  trunk  up      none                        10G(D) 1
Eth1/8        1       eth  trunk  up      none                        10G(D) 1
nycmesh-sn3-n5k(config)#


nycmesh-sn3-n5k(config)# show lacp port-channel
port-channel1
  System Mac=8c-60-4f-50-45-fc
  Local System Identifier=0x8000,8c-60-4f-50-45-fc
  Admin key=0x8000
  Operational key=0x8000
  Partner System Identifier=0xffff,e4-43-4b-18-25-f0
  Operational key=0xf
  Max delay=0
  Aggregate or individual=1
  Member Port List=7-8

port-channel2
  System Mac=8c-60-4f-50-45-fc
  Local System Identifier=0x8000,8c-60-4f-50-45-fc
  Admin key=0x1
  Operational key=0x1
  Partner System Identifier=0x0,0-0-0-0-0-0
  Operational key=0x0
  Max delay=0
  Aggregate or individual=0
  Member Port List=5-6

nycmesh-sn3-n5k# show lacp counters
                    LACPDUs         Marker      Marker Response    LACPDUs
Port              Sent   Recv     Sent   Recv     Sent   Recv      Pkts Err
---------------------------------------------------------------------
port-channel1
Ethernet1/7        1245   122      0      0        0      0        0
Ethernet1/8        1230   90       0      0        0      0        0

port-channel2
Ethernet1/5        150    6        0      0        0      0        0
Ethernet1/6        150    6        0      0        0      0        0

port-channel16
Ethernet1/27       15676801567441  0      0        0      0        0
Ethernet1/28       15233911523177  0      0        0      0        0

  • Some resources
    • Cisco PDF for port-channel configuration with examples, details, etc. Very useful https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/7-x/interfaces/configuration/guide/b_Cisco_Nexus_9000_Series_NX-OS_Interfaces_Configuration_Guide_7x/b_Cisco_Nexus_9000_Series_NX-OS_Interfaces_Configuration_Guide_7x_chapter_0111.pdf
    • https://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/configuration/nxos/Cisco_Nexus_5000_Series_NX-OS_Software_Configuration_Guide_chapter9.html has info on how to set up a VLAN in trunk mode, which I think is what we want
    • select multiple interfaces https://www.cisco.com/c/en/us/td/docs/ios/interface/configuration/guide/ir_ifrange.html
    • clear interface counters https://community.cisco.com/t5/switching/how-to-clear-the-interfaces-counter-in-cisco-switches/td-p/2709137
    • briefly describes cisco lacp active vs passive vs on https://www.grandmetric.com/knowledge-base/design_and_configure/how-to-configure-lacp-on-cisco/
    • cisco command reference for different LACP configuration options, I didn't need this https://www.cisco.com/c/en/us/td/docs/optical/cpt/r9_3/command/reference/cpt93_cr/cpt93_cr_chapter_01000.html
    • similar but not exact web version of the PDF for LACP cisco, has the general gist of what I needed https://www.cisco.com/c/en/us/td/docs/ios/12_2sb/feature/guide/gigeth.html
    • Apparently I need to run no shutdown and that resets the up/down state of ports https://networkengineering.stackexchange.com/questions/56548/what-does-no-shutdown-command-do-cisco
    • https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/6-x/interfaces/configuration/guide/b_Cisco_Nexus_9000_Series_NX-OS_Interfaces_Configuration_Guide/b_Cisco_Nexus_9000_Series_NX-OS_Interfaces_Configuration_Guide_chapter_0110.html another guide on how to set up LACP, to some extent

Proxmox/Debian Setup

  • Goals
    • The host has four 10G network adapters, two of which are connected to the Cisco switch. The two connected adapters should run in an 802.3ad LACP LAG for redundant + aggregated link speed.
    • The host should also be able to talk using tagged traffic on VLAN 32, which is where the other Proxmox host Jon communicates. This will be configured as a trunk port, meaning all traffic that is not tagged will be ignored
  • Configuration to some degree can occur in the Proxmox GUI, but if the switch is already configured for VLANs and LACP, a connection may not be possible. Instead, use the virtual console of the iDRAC to type and configure via the CLI of Proxmox
  • All configuration occurs within /etc/network/interfaces
  • After modifying, the settings can be applied by restarting the service systemctl restart networking
  • The following config is pulled from one of the hosts. Note that the iface names might vary from host to host, so while one host may be enl1np0 another host may just be eno0
root@nycmesh-713-r640-01:~# cat /etc/network/interfaces
auto lo
iface lo inet loopback

iface eno1np0 inet manual
iface eno2np1 inet manual
iface eno3np2 inet manual
iface eno4np3 inet manual

auto bond0
iface bond0 inet manual
        bond-slaves eno1np0 eno2np1
        bond-miimon 100
        bond-mode 802.3ad
        bond-xmit-hash-policy layer2+3

iface bond0.32 inet manual

auto vmbr0v32
iface vmbr0v32 inet static
        address 10.70.90.195
        gateway 10.70.90.1
        bridge-ports bond0.32
        bridge-stp off
        bridge-fd 0

iface idrac inet manual

source /etc/network/interfaces.d/*
  • The following version is marked up to indicate the purpose of each line
# declares and configures the loopback interface
auto lo
iface lo inet loopback

# declares and configures the "raw" adapter interfaces
iface eno1np0 inet manual
iface eno2np1 inet manual
iface eno3np2 inet manual
iface eno4np3 inet manual

# delcares the LACP 802.3ad LAG port-channel bond
auto bond0
iface bond0 inet manual
        bond-slaves eno1np0 eno2np1 # defines which adapters are part of the LACP bond
        bond-miimon 100 # default, defines the link monitoring frequency
        bond-mode 802.3ad # defines the type of bond (round-robin, active-backup, etc) and 802.3ad is the LACP standard
        bond-xmit-hash-policy layer2+3 # defines the method by which traffic will be transmitted across the interfaces of the bond

# declares an interface configured for VLAN 32 on the LACP bond interface
iface bond0.32 inet manual

# declares a Linux Bridge
auto vmbr0v32
iface vmbr0v32 inet static
        address 10.70.90.195 # defines the static IP (and subnet if desired, via /24, /28, etc.)
        gateway 10.70.90.1 # defines the gateway through which traffic will pass
        bridge-ports bond0.32 # defines the interface the Bridge is connected to. In this case VLAN 32 on the LACP bond is desired, and an interface was set up a few lines above for this
        bridge-stp off # turns off spanning tree protocol for loop prevention
        bridge-fd 0 # default forwarding delay, seen in all tutorials

# defines the interface that the iDRAC operates on. This won't be used
iface idrac inet manual 

# Fetches further configuration from files within the following folder
source /etc/network/interfaces.d/*
  • Resources
    • Very helpful Proxmox official guide for VLANs and LACP bonding all on one page at the same time https://pve.proxmox.com/wiki/Network_Configuration#sysadmin_network_vlan
    • Proxmox community sample LACP config, I didn't end up using this but good to know https://forum.proxmox.com/threads/proxmox-lacp-bonding-and-tp-link-managed-switch.130789/
    • Proxmox another community sample LACP config https://forum.proxmox.com/threads/lacp-trunk-on-two-ethernet-ports.146386/
    • General debian guide for bonding/LACP https://wiki.debian.org/Bonding
    • Another community LACP and VLAN guide https://forum.proxmox.com/threads/setting-up-lacp-bond-with-vlan-trunk-and-bridge.93331/
    • https://wiki.debian.org/NetworkConfiguration#Reinitialize_new_network_setup once a change is made in /etc/network/interfaces, apply it with sytemctl restart networking
    • I left the subnet off the end of the linux /etc/network/interfaces address line, which seems to resolve to a /32 when I run ip a. According to https://networkengineering.stackexchange.com/questions/34587/why-do-i-need-to-specify-a-subnet-mask-on-interface it just seems to dictate which pings/traffic need to hit the router and which can go directly to another device without a router involved. Since we use a mix of /26, /30/ 24, etc I figure the /32 is safe